We are very sorry that your purchase was incomplete. Please contact us to arrange for the missing item to be sent to you. We will need to know the tool kit model number, which item is missing, and your personal information in order to get the replacement to you. Email us, or call RotoZip Customer Service at 1-877-768-6947. Our hours are Monday through Friday 8:00AM to 6:00PM, Central Standard Time.
Click Here to find the owner's manual for your RotoZip tool. If you need specific help with your tool/attachments, you will find step-by-step instructions in your Owner's Manual online. If you still need assistance, feel free to contact us at 1-877-ROTOZIP (1-877-768-6947), and we will do our best to answer your question quickly and helpfully.
If your electric power tools have been submerged in water for an extended period of time, it is very important that you properly clean, dry, and safety test them before attempting to put them to use. Water is an extremely effective conductor of electricity and failure to properly inspect and test your electric tool could result in an unsafe and dangerous situation. Water contamination can have a detrimental effect on both the electrical and mechanical portions of the tool; therefore a complete examination is required prior to using your tool. We strongly encourage this evaluation and testing be performed by a Bosch Factory or Authorized Service Center or qualified electric motor repair facility.
Electrical
The motor, including the armature, field, brushes, and springs should be completely disassembled and blown off with clean, dry compressed air. Armatures and fields should be safety tested using a high voltage test according to manufacturer’s and UL specifications Brush springs or holders that appear rusted should be replaced All wiring connections, including field and switch leads, must be clean and dry Make sure to blow out all cavities in the motor housing where moisture can be trapped Clean, dry, and repack bearings. Sealed bearings that run rough should be replaced Inspect the power cord for any sign of water contamination such as swelling or discoloration and replace if necessary. The complete tool must be safety tested before use with a high voltage test according to manufacturer’s and UL specifications
Mechanical
Clean and re-lubricate the gear box according to manufacturers specifications Clean, dry, and repack bearings. Sealed bearings that run rough should be replaced Chucks, bit, and blade holders can be sprayed with a WD-40 type lubricant and then blown off with clean dry compressed air. Check circular saw lower guards, these should move freely and close quickly. If not working properly replace lower guard and bearing plate – do not lubricate or apply oil.
Batteries and Chargers, Cordless Tools
Battery packs have internal cells and connections that can become corroded and/or rust when water enters the case through a vent hole. Such batteries will exhibit lower power and have reduced capacity to be charged. The vent holes may also become clogged and non-functional. Batteries have no serviceable internal components and must therefore be replaced under such conditions.
Mechanical
Blow off exposed terminals with clean, dry compressed air and allow to sit for 48 hours, longer if possible, to allow for evaporation.
For further assistance contact RotoZip Customer Service at 1-877-ROTOZIP (1-877-768-6947).
We have a small selection of service parts available for purchase directly through RotoZip if you are located in the United States or Canada. Parts may be ordered by calling RotoZip Customer Service at 1-877-768-6947. Our hours are Monday through Friday from 8:00AM to 6:00PM, Central Standard Time. Should you decide to order by phone, please have your tool's model and serial numbers ready. We will also need your phone number and address to process your order.
The attachment chart below indicates compatibility of RotoZip® tools and attachments. Keep in mind some attachments have been discontinued. Attachment Compatibility Chart
Always enter the material at a 45° angle and then smoothly bring the tool up to a 90° angle. 1. Use moderate steady pressure to guide your tool when cutting. Let the tool do the work. Too much pressure can result in bits breaking. 2. While Spiral Saws will cut in any direction, in order to optimize cutting performance and reduce the risk of breaking bits, most materials should be cut in a clockwise direction. The exception is when cutting around an outlet box in drywall - then it's best to work counter-clockwise. 3. When inserting bits into the tool, leave 1/8" of exposed shank above the collet or chuck. Tightening the collet or chuck over the cutting surface of the bit reduces flexing and can lead to broken bits. 4. Our bits are designed to cool themselves. The Zip®Bit should be at least 1/8" past the material being cut. If the bit is not extended all the way through the material, it will start burning and cause the bit to break prematurely. So, make sure to adjust your base plate to the proper cutting depth. 5. Spiral Saws spin at up to 30,000 RPM so keep the tool moving at a steady speed while letting the tool do the work. 6. The base plate must remain flush with the material at all times. This prevents uneven pressure from being placed on the bit, which could result in premature bit breakage.